Product Description
Ford Fairlane 1955-1970 Complete Air Ride Suspension Lowering System Kit
For sale: a complete air ride suspension system built for the 1955-1970 Ford Fairlane (also fits the Ford Torino from the same era), engineered by True Suspension to lower the car up to 4-5", with a suggested drive height of 3" below stock — enough drop to make a real statement without sitting so low you lose practical ride height for daily driving.
Unlike our bolt-on kits, this Fairlane system requires welding and modification: front air spring mounts weld on at the top and bolt on at the bottom, and the rear setup goes further, with weld-on mounts positioned under and at the rear of the axle to maximize suspension travel. The rear end gets a heavy-duty triangulated 4-link, also weld-on, built specifically to improve traction and handling rather than just support the air springs. A front shock relocation kit with 2 gas shocks and upper weld-on relocation brackets keeps your shocks functioning at the new ride height. The air spring setup itself mixes 2 D2 series springs with 2 of the larger 2600 series springs, a different combination than our other classic kits use.
Powering the system is a 1/3 HP, 100% duty cycle compressor with a 40 amp relay, feeding a 3-gallon, 5-port stainless steel tank rated to 1000 PSI. Control comes through a non-electric Active Air pneumatic paddle switch with a 150 PSI lighted gauge, backed by a 120 PSI pressure switch that maintains air automatically. A 50 ft roll of 1/4" air hose and a complete fitting pack, including the tank drain plug, finish out the kit.
Given the amount of welding and fabrication this system requires, we strongly recommend a professional installer with the right equipment perform this install.
What's Included – Ford Fairlane 55-70 Complete Air Ride Suspension System
- Front air spring mounts (weld-on upper, bolt-on lower; welding and modification required)
- Rear air spring mounts (weld-on under and rear of axle, maximized for travel)
- Front shock relocation kit with 2 gas shocks and weld-on relocation brackets
- Rear weld-on heavy-duty triangulated 4-link
- 2x 2500 D2 series air springs, 2x 2600 series air springs
- 1/3 HP 100% duty cycle compressor with 40 amp relay
- 3-gallon, 5-port stainless steel air tank (1000 PSI max rating)
- Active Air pneumatic paddle switch controller with 150 PSI lighted gauge
- 120 PSI pressure switch for constant air maintenance
- 50 ft roll of 1/4" air hose with complete fitting pack and tank drain plug
- Fits 1955-1970 Ford Fairlane and Torino
- Designed in the USA
- 1 Year Warranty against manufacturer defects
What Sets This Fairlane System Apart
- Delivers up to 4-5" of drop, with a 3-inch-below-stock drive height as the practical daily target
- Weld-on 4-link improves traction and handling, not just ride height
- Mixed D2/2600 spring combination sized specifically for this chassis's weight and geometry
- Rear mounts positioned to maximize suspension travel, not just support the drop
NOTE: We suggest a professional installer with proper equipment to perform the installation of this kit, given the amount of welding and fabrication involved.
Please note: Neither the manufacturer nor the seller assumes liability for injury, loss, or damage arising directly or indirectly from installing or using this kit. The user assumes all responsibility in connection with this custom suspension kit and its appropriate use.
Returns: Subject to a 15% restocking fee. Items must be returned within 30 days of purchase and in unused condition — contact us with details before returning. If you have any concerns before leaving feedback, please contact us; we're here to help with any customer service issue.
Browse the full Ford Fairlane Custom Air Ride Kits category, or explore other classic platforms in our Custom Air Ride Kits selection, including Ford Falcon and Ford Galaxy. Our Classic Car Builder's Guide to 4-Link Suspension & Air Bags covers more on planning a weld-on 4-link build.
